Baxi Boiler Error Codes

Baxi Boiler Error Codes

Baxi Error Codes

Baxi have one of the best reputations in the market for delivering top quality boilers.

Occasionally some things can go wrong, that’s why we’ve created our handy at-a-glance table of Baxi error codes below and our guide to Common Baxi Boiler Problems.

Should you need professional help with your broken boiler, then simply use one of our enquiry forms and we will connect you with the best heating engineers local to you.


Is your Boiler broken?

 

Get quotes to Get a Repair Quote Now

 



Platinum error codes
EcoBlue error codes
EcoBlue Advance / Ecoblue Regular Gas Boiler Flashing Light Error Codes
200 / 400 Combi Error Codes
Duo-tec/Megaflo error codes
600 Combi Error Codes
MainEco error codes
Avanta error codes
GA Range error codes
Baxi Solo error codes
Error Code E133 and E28

Baxi Platinum Error Codes

Listed below are the most common error codes that you might see on your Baxi Platinum combi range of boiler.

Fault Code Possible Cause
E20 Central heating NTC error
E28 Error with the NTC flue. Possible air pressure switch error. Blocked flue or condensate or wing fault
E50 Hot water NTC error
E110 Thermostat operated safety
E119 Water pressure switch error – Not operated.
E125 Primary circuit error circulation fault
E130 FLue NTC Operation error
E133 Gas supply Error or flame failure
E160 Fan Error / Fan Wiring Error
E193 Pre-circulation error
Back to top
Get a repair quote now

Baxi EcoBlue Error Codes

Listed below are the most common error codes that you might see on your Baxi boiler.

Fault Code Possible Cause
110 Overheated – try bleeding your radiators
117 Water pressure too high
118 Water pressure too low
125 Water circulation fault
133 Safety time to establish flame exceeded
E10 Outdoor Sensor Error
E20 Central Heating Thermistor Sensor Fault
E28 Flue Thermistor Fault
E54 HW Flow Sensor Fault
E78 Water Pressure Sensor Fault
E100 Internal Clock Time Error on PCB
E109 Poor Circulation
110 Overheat – try bleeding your radiators
111 Maximum Limit of Flow Temperature
117 Water pressure too high
118 Water pressure too low
119 System Pressure Low
125 Water circulation fault
127 Legionella Protection Temperature not reached
128 Loss of flame during operation
133 Safety time to establish flame exceeded
153 Forced reset unit unlocked
160 Fan Fault
162 Air pressure switch error
164 Heating flow switch error (Ireland) Pressure Sensor Error (UK)
166 Air Pressure Switch Fault
270 Dry Fire
432 Earth connector error
433 Heat exchanger temperature exceeded (greater than 95 degrees)
Back to top
Get a repair quote now

EcoBlue Advance / Ecoblue Regular Gas Boiler Flashing Light Error Codes

Listed below are the flashing light error codes for the EcoBlue Advance Regular Gas Boiler and the EcoBlue Regular Boiler.

Fault Code Possible Cause
1 Green Flash Boiler temp reached – No action required
3 Green Flashes Temporary Flame Loss – boiler will self reset, if continues will go to 3 Red Flashes
4 Green Flashes Communication error between PCB and Control – temporary error, will self reset
5 Green Flashes Parameter Error On PSU/PCB – temporary error, will self reset
6 Green Flashes Miscellaneous Error – temporary error, will self reset
1 Red Flash Sensor Error; Sensor Fault, Temperature Fault or Flow Fault
2 Red Flashes Boiler overheat tripped
3 Red Flashes Ignition fault. Boiler has attempted to light 5 times and failed
4 Red Flashes Fan Fault
5 Red Flashes Parameter or PSU Error
6 Red Flashes Miscellaneous Error
Back to top
Get a repair quote now

Baxi Duo-tec/Megaflo Error Codes

Listed below are the most common error codes that you might see on your Baxi Duo-tec/Megaflo range of boiler.

Fault Code Possible Cause
E10 Outdoor sensor fault
E20 Central Heating Thermistor Sensor error
E28 Flue Thermistor error
E110 Boiler Overheat error
E119 Low water pressure error
E125 Primary Water Circulation error
E131 Flue overheat lockout error
E133 Ignition error
E160 / E161 Fan error
E164 Pressure Sensor Fault
E167 PCB Error
E168 PCB lock out Error
E193 Circulation Error
Back to top
Get a repair quote now

Is your Boiler broken?

 

 


Baxi 200 / 400 Combi Gas Boiler Error Codes

Listed below are Error codes that could appear on either your Baxi Combi 200 Boiler or your Baxi 400 Combi boiler.

Fault Code Possible Cause
H.01 – .00 Loss of communication between gas valve and boiler board. Possible faul in air or gas unit / loose connection to gas valve
H.01 – .05 Difference between the flow and return temperature has exceeded / sensor error / no or insufficient circulation
H.01 – .08 Sensor fault / Flow temperature increasing to fast in heating mode / no or insufficient circulation
H.01 – .14 Maximum flow temperature value exceeded / no or insufficient circulation / no or insufficient circulation ( temporary fault )
H.01 – .18 No circulation of water. No or insufficient circulation. Sensor error.
H.01 – .21 Temporary error- Flow temperature increasing too fast in DHW mode. No or insufficient circulation. Sensor error.
H.02 – .02 Temporary Error – No input of parameters C1/C2. PCB not configured.
H.02 – .03 Temporary error- Incorrect configuration settings C1/C2.
H.02 – .04 Temporary error- Parameter fault. Incorrect parameters.
H.02 – .06 Temporary error – System water pressure / Water leak on boiler/ Water leak on system.
H.03 -.00 Temporary error with Communication fault / NTC flue sensor error. Sensor not connected or has a bad connection
H.03 – .01 Communication error with the HMI PCB
H.03 – .02 Flame error – No flame during operation.
E.00 – .04 Return temperature sensor open-circuit. Sensor not or badly connected.
E.00 – .05 Return temperature sensor short-circuit. Sensor not connected or badly connected
E.01 – .02 Temperature measured by return sensor greater than flow sensor.
E.01 – .04 Loss of flame detected 5 times in 24 hours (With burner on).
E.01 – .11 Incorrect fan speed. External draught over the boiler. Defective gas/air unit.
E.01 – .12 Requires Reset – Temperature measured by return sensor greater than flow temperature.
E.01 – .17 Requires Reset – No circulation. Sensor fault either not connected or has a bad connection
E.01 – .20 Maximum flue gas temperature reached. No circulation. Sensor fault.
E.02 – .00 Boiler reset – Reset button has been pressed.
E.02 – .07 No or low system water pressure. system pressure less than 0.5bar
E.02 – .16 CSU time-out. PCB damage.
E.02 – .17 loss of communication between gas valve and boiler PCB. Fault in air/gas unit.
E.02 – .19 Jumper 1 changed. Check position of jumper 1.
E.02 – .20 Jumper 2 changed. Check position of jumper 2.
E.02 – .21 Jumper 3 changed. Check position of jumper 3.
E.02 – .47 Wiring to external device error.
E.02 – .48 Configuration to external device unsuccessful. Check pairing to external.
E.04 – .00 Gas valve error. Gas valve not detected.
E.04 – .01 Flow temperature sensor short-circuited. Sensor not or badly connected. Bad connection. Sensor fault.
E.04 – .02 Permanent Fault – Flow temperature sensor open-circuited. Sensor not or badly connected. Bad connection. Sensor fault.
E.04 – .03 Permanent Fault – Critical flow temperature reached. Non-existent or insufficient circulation.
E.04 – .04 Permanent Fault – Flue temperature sensor short-circuited. Sensor not or badly connected. Bad connection. Sensor fault.
E.04 – .05 Permanent Fault – Flue temperature sensor open-circuited. Sensor not or badly connected. Bad connection. Sensor fault.
E.04 – .06 Permanent Fault – Critical flue gas temperature value reached. No circulation. Sensor fault.
E.04 – .08 Permanent Fault – Maximum safe temperature value reached. (Safety thermostat open-circuited). No circulation. Sensor not or badly connected. Bad connection. Sensor fault.
E.04 – .10 Failure to light (could be gas supply issue).
E.04 – .12 Permanent Fault – False flame signal. Short-term fluctuation of the mains. Ionization current present even though there is no flame. The burner remains very hot (CO2 too high). Defective gas/air unit.
E.04 – .13 Permanent Fault – Fan rotor blocked. Fan seized. Wiring to fan damaged.
E.04 – .17 Permanent Fault – Problem with gas valve. Defective gas/air unit.
Back to top
Get a repair quote now

Baxi 600 Combi Gas Boiler Error Codes

Listed below are some of the fault codes that could appear on your Baxi 600 combi gas boiler.

Fault Code Possible Cause
E09 Gas valve connection cable.
E10 External probe fault.
E12 Differential water flow switch fault (still open).
E13 Differential water flow switch fault (still closed).
E15 Gas valve command fault.
E20 Central heating NTC fault.
E28 Flue NTC fault.
E40 Central heating return NTC fault.
E50 DHW NTC sensor fault (tank boiler) (s.c.) OR DHW NTC sensor fault (tank boiler) (o.c.).
E83/E84/E85/E86/E87 No communication.
E109 Pre-circulation fault.
E110 i) Boiler max temperature exceeded for gradient (probable pump jammed or air in the
circuit). OR ii) Boiler max temperature exceeded for overtemperature (probable pump jammed or
air in the circuit). OR iii) Safety thermostat sensor tripped.
E118 Primary system water pressure too low (< 0.5 bar).
E125 Circulation fault (primary).
E128 Frequent flame failure (12 times).
E129 Safety error for frequently loss of flame with max correction during the ignition during Calibration Function.
E130 Flue thermostat sensor tripped (lockout).
E133 Failure to light (could be a gas supply issue).
E134 Elapsed time gas valve open without gas
(short request in a short period)
E135 Interruption of gas supply (internal error).
E154 Flow/return sensor temperature test.
E160 Fan or fan wiring fault.
E163 Domestic Hot Water NTC sensor fault (s.c.) OR Domestic Hot Water NTC sensor fault (o.c.).
E270 Circulation fault (dry fire).
E317 Wrong power supply electrical frequency (Hz).
E321 Hot water NTC fault.
E384 False flame.
E385 Under voltage.
E430 Water pressure temporary test.
E430 + Flame ‘crossed’ Water pressure test failed.
Back to top
Get a repair quote now

Baxi MainEco Error Codes

Listed below are the most common error codes that you might see on your Baxi Baxi MainEco range of boiler.

Fault Code Possible Cause
1 Green Flash Boiler temperature reached – no action required
3 Green Flashes Temporary flame loss – this is a temporary error, the system should reset on its own
4 Green Flashes Communication error between PCB and Control – this is a temporary error, the system should reset on it’s own
5 Green Flashes Parameter Error On PSU/PCB – this is a temporary error, the system should reset on it’s own
6 Green Flashes Miscellaneous Error
1 Red Flash Sensor Error; Sensor Fault, Temperature Fault or Flow Fault – this is a temporary error, the system should reset on it’s own
2 Red Flashes Boiler overheat tripped
3 Red Flashes Ignition fault. Boiler has attempted to light 5 times and failed
4 Red Flashes Fan Fault
5 Red Flashes Parameter or PSU Error
6 Red Flashes Miscellaneous
Back to top
Get a repair quote now

Is your Boiler broken?

 

Get quotes to Get a Repair Quote Now

 


Baxi Avanta Range Error Codes

Listed below are the most common error codes that you might see on your Baxi Avanta range of boiler.

Fault Code Possible Cause
E0 Temperature sensor fault
E1 Overheated – try bleeding your radiators
E2 Poor Circulation – try bleeding your radiators
E3 PCB fault
E4 Ignition failure – try bleeding your radiators
E10 Poor/No circulation
E12 PCB Fault
E13 Heat exchanger thermal fuse tripped
E83 / 84 / 85 / 86 / 87 Fan fault normally E8
Back to top
Get a repair quote now

Baxi GA Range Error Codes

Listed below are the most common error codes that you might see on your Baxi GA range of boiler.

Fault Code Possible Cause
E53 Poor combustion – flue terminal may be blocked
E110 Overheated – try bleeding your radiators
E117 System water pressure high – try bleeding water from your radiators
E118 System water pressure low
E125 Overheat – try bleeding your radiators
E133 Gas supply fault
E4 Ignition failure
E09 Gas valve wiring fault
E10 Outdoor sensor error
E15 Gas valve connection fault
E20 Central heating thermistor sensor fault
E28 Flue thermistor fault
E40 Central heating return thermistor fault
E53 Flue obstruction
E55 Calibration required
E78 Water pressure sensor fault
E92 Combustion test alarm during auto-setting
E109 Poor circulation
E110 Boiler overheat tripped
E117 System pressure high (>2.9 Bar)
E118 System pressure low( < 0.5bar)
E125 Primary water circulation fault
E128 Loss of flame during operation
E129 Loss of flame during calibration
E133 Ignition fault
E135 Internal error
E154 Primary flow fault
E160 Fan fault
E270 Dry fire
E317 Wrong power supply (Hz)
E321 Not water thermistor fault
E384 Flame detected when gas valve off
E385 Low voltage (less than 195v)
Back to top
Get a repair quote now

Baxi Solo Error Codes

Listed below are the most common error codes that you might see on your Baxi Solo Regular range of boiler’s.

Fault Code Possible Cause
FLASH FLASH ON Fan Error
FLASH OFF FLASH Voltage less than 180V
FLASH OFF ON Overheat lockout
FLASH ON FLASH PCB Error
FLASH ON ON PCB fault
OFF OFF OFF No power
ON FLASH FLASH Circulation error or dry fire
ON FLASH ON Thermistor Error
ON OFF FLASH Live and neutral reversed error
ON OFF ON Ignition lockout error
ON ON FLASH PCB error
ON ON ON Low voltage wiring harness error
Back to top
Get a repair quote now

Error Code E133 and E28

If you’re seeing either of these two error codes on your Baxi boiler, this is due to your condensate pipe being frozen. In the cold winter months this can happen easily as the condensate pipe runs outside. You can fix this issue by thawing out the pipe (if you feel confident to), find out everything you need to know about how to do it with our guide to thawing a frozen condensate pipe.


Is your Boiler broken?

 

Get quotes to Get a Repair Quote Now